adhesion strength的例句大全

Rubber adhesive packing tape, gook adhesion strength, water and cold proof.

感压性牛皮纸胶带, 粘性佳, 防水及耐候性优良,主要用于纸箱包装.

Both of these physical phenomena to increase adhesion strength are very important.

上述两种物理现象对于提高粘合力都是十分重要的.

In addition, the adhesion strength also related with rough surface.

另外, 粘附强度还与表面粗糙程度有关.

The designer should the experience, the formula rationally and calculate the internal and adhesion strength accurately.

工程实践中,设计者应当总结经验, 对锚筋内力、桩承载力和粘结力采用合理公式并准确计算.

The adhesive has higher adhesion strength than the conventional two-component PU adhesive used for laminating leather.

与常用的复合革用双组分聚氨酯胶粘剂相比,该胶粘剂具有较高的粘接强度.

The results showed that the composite emulsion had more excellent adhesion strength and water resistance.

结果表明:与普通乳液相比,复合乳液的干态粘接强度和耐水性明显提高.

The results were as follows: In the gel process, alkaline environment was more conducive to maintain activity of Anabaena aquae, reduce adhesion among particles and improve strength of particles.

研究结果如下：在凝胶过程中，偏碱性环境更利于水华鱼腥藻保持活性、降低颗粒之间粘连性和提高颗粒强度。

Film properties including surface drying time, luster value, shock strength, adhesion and flexibility were tested according to standard methods for coating.

同时用涂料标准方法测定了这些样品的漆膜的表干时间、光泽值、冲击强度、附着力、柔韧性等。

The effects of polymer dry powder on the adhesion strength of cement mortar at different curing conditions

不同养护条件下聚合物干粉对水泥砂浆粘结强度的影响

The results show that it is related to viscosity, stability, dry speed, adhesion strength.

结果表明，这些因素对胶粘剂的粘度、稳定性、干燥速度和粘贴强度有很大的影响。

The matrix of Chinese Medicine Patcher was studied by uniform design and taking adhesion strength as index.

采用均匀设计法，以粘着强度为指标，筛选中药巴布剂基质。

The effect of monomer ratio, the kind and concentration of keying agent on adhesion strength is also studied.

研究了单体配比、增粘剂种类、增粘剂用量对剥离强度的影响。

The manufacture process was improved from the first cold bonding-post curing to primary cure by using the mold having chevron cell, and the adhesion strength between the chevron type of pattern and the belt body was improved, and the conveyance capability was significantly increased.

制作工艺由起初的冷粘合二次硫化改进为在硫化机上加装人字花纹模具一次整体硫化，提高了花纹和带体间的粘合强度，明显地增加了输送带的输送量；

( Influences) of 12 kinds of adhesives on strength and burning properties of the formed charcoal were investigated. Suitable adhesion agent was selected, and technology and formula were optimized.

通过考察12种胶粘剂对炭块的强度和燃烧性质的影响，优选出适用的粘结剂，并对生产工艺与配方进行了优化。

Inadequate bonding strength of adhesion agent was traditionally considered to cause project quality problems, but the traditional bonding mode is only on the basis of experience.

在外墙外保温的工程质量问题中，传统认为是黏结强度不够的原因，而传统的黏结方式也只是根据经验而定的。

Study and Measurement of Adhesion Strength and Film Stress of Ag-Cu/ Ti Substrate Bilayer Films Composite Systems

Ag-Cu/Ti双金属膜结合强度及应力研究

Interfacial adhesion strength of composite is characterized by the methods of torsional braid analysis.

使用扭辫分析对复合材料界面粘合强度进行了表征.

Adhesion is the bond strength measurement of a coating to a substrate.

粘附力是指涂料粘结到基底材料上的粘接强度衡量标准.

Polyolefin have low adhesion strength because of low surface energy base adhesive is prepared with acrylicresin.

聚烯烃具有低的表面能,对于未处理聚烯烃表面的粘接,采用普通的胶粘剂,通常难以得到良好的效果.